Industrial Electric Pear Peeler Overview

The Electric Pear Peeler is an automatic six-station machine for processors that need continuous feeding, orientation, and mechanical contour peeling. Pears enter through a multi-lane feeder, are separated into individual paths, and are presented to the peeling stations without dedicated loading operators. The machine is rated for up to 72 pears per minute, equivalent to up to 4,320 pears per hour under suitable product and operating conditions.
Fruit geometry remains central to a successful configuration. The specified working range covers diameters from 50 to 90 mm and fruit heights up to 140 mm. Because European pears, Asian pears, and similar varieties differ in taper, firmness, stem condition, and surface irregularity, representative samples should be reviewed before tooling and settings are finalized. AGICO uses these samples to discuss orientation, holder contact, peeling depth, and the required finished appearance.
Key Features for Continuous Pear Processing
-
Automatic Multi-Lane Feeding
The feeder separates incoming pears and guides them toward six processing lanes. This reduces reliance on manual placement, but stable output still depends on controlled bulk loading and fruit that can move without bridging.
-
Shape-Following Peeling
Mechanical contour peeling follows the pear surface instead of applying one fixed cylindrical cut. Adjustable depth helps the processor balance peel removal with product retention for the selected variety and maturity.
-
PLC-Based Operation
A PLC and operator panel centralize routine control. Recipe changes should be supported by documented settings for fruit size, rotation, peeling depth, and line speed rather than frequent uncontrolled adjustment.
-
Food-Grade Stainless Construction
Stainless-steel construction supports washdown planning and inspection around food-contact zones. Cleaning access, chemical compatibility, and drainage practice should be agreed for the buyer's sanitation program.
Configuration and Fruit Selection
| Parameter | Specification |
|---|---|
| Processing Capacity | Up to 72 pears/min |
| Equivalent Output | Up to 4,320 pears/h |
| Peeling Stations | 6 |
| Feeding Method | Automatic multi-lane feeding and orientation |
| Installed Power | Approximately 6.5 kW |
| Machine Dimensions | Approximately 2,650 × 1,660 × 2,510 mm |
| Machine Weight | Approximately 2,000 kg |
| Minimum Air Pressure / Consumption | 5 bar / Approximately 50 NL/min |
| Minimum Water Pressure / Consumption | 3 bar / Approximately 4.6 L/min |
| Fruit Size | 50–90 mm diameter; maximum 140 mm height |
| Peeling Method / Depth | Mechanical contour peeling / Adjustable |
| Control / Construction | PLC with operator control panel / Food-grade stainless steel |
Products and Production Uses
Suitability should be confirmed with representative fruit and the required downstream format.
European Pears
Elongated and tapered varieties require reliable orientation and sample-based holder selection. Incoming fruit should be graded so extreme size differences do not interrupt feeding.
Asian Pears
Rounder Asian pears may use a different contact path and peeling recipe. Firmness and skin adhesion should be checked because both affect the practical peeling depth.
Fresh-Cut Preparation
Peeled pears can move to coring, slicing, dicing, or packing. The receiving equipment must match the peeler's discharge rate and protect the fruit from unnecessary impact.
Further Processing
For puree, canning, drying, or ingredient preparation, buyers should define the required surface finish and acceptable remaining peel before confirming settings.
How the Electric Pear Peeler Works
01–05
Feed and separate: pears enter the automatic multi-lane feeder at a controlled rate. Orient: lane components guide each pear toward a repeatable presentation. Transfer: individual fruit moves into one of six peeling stations. Contour peel: the mechanical tool follows the surface at the selected depth. Discharge: peeled fruit leaves the processing area for inspection or the next operation. Stable performance depends on suitable grading, correctly matched holders, clean contact parts, and utilities maintained above the stated minimum pressures.
At AGICO, we recommend confirming the upstream feed height, available floor space, discharge direction, and downstream accumulation before the final layout is approved. The machine footprint is approximately 2,650 × 1,660 × 2,510 mm and its approximate weight is 2,000 kg, so access, foundations, lifting routes, and maintenance clearance must be considered early.

Cleaning, Changeover, and Routine Checks
Before sanitation, isolate electrical, pneumatic, and water supplies according to the plant's safety procedure. Remove loose peel and product fragments from the feeder, holders, peeling area, guards, and discharge zones before applying the approved cleaning method. Avoid directing uncontrolled water toward electrical enclosures, sensors, or the operator panel.
During a variety or size change, inspect the lane guides, holders, peeling tools, and depth settings. A short controlled trial should confirm orientation and finished appearance before normal production resumes. Operators should also check for worn contact parts, loose fasteners, damaged guards, blocked drains, and abnormal air or water consumption. Preventive replacement intervals should be based on actual operating hours, fruit condition, and the sanitation schedule. Record the approved settings for repeat production runs.
For line planning, allow operators to see the infeed lanes, peeling stations, and discharge area without removing guards. Provide convenient isolation points and sufficient space for tool inspection. Clear access reduces changeover delays and helps the sanitation team verify that peel fragments have been removed from hidden contact zones.
Frequently Asked Questions
-
Can the machine always reach 72 pears per minute?
The figure is an upper rated capacity. Actual output depends on pear size, shape consistency, firmness, feeding continuity, orientation, peeling depth, and downstream acceptance.
-
Are dedicated loading operators required?
Dedicated manual loading at each peeling station is not required with the automatic feeder. Personnel are still needed for bulk-feed supervision, quality checks, sanitation, and line coordination.
-
What information is needed for configuration?
Provide representative pears, diameter and height ranges, variety, maturity, target finish, expected input, utility conditions, floor plan, and the required upstream and downstream interfaces.
-
How is peeling depth selected?
Depth is adjustable and should be established through a controlled sample trial. The setting must account for skin adhesion, surface defects, fruit firmness, and the acceptable finished appearance.
Hot Tags: electric pear peeler, China electric pear peeler manufacturers, suppliers, factory, Citrus Cutting Machine, Citrus Pulp Separation Machine, Fruit Vegetable Washing Processing Line, Jujube Pitting Machine, Mango Pulp Concentrate Processing Line, Vegetable Peeling Machine
